You are here: Home » Resources » News&Blog/Press Release » Custom Magnetics Case Studies » Custom Winding Structure: In-Process Three-Wire Twisting for an EI14 Transformer

Custom Winding Structure: In-Process Three-Wire Twisting for an EI14 Transformer

Views: 50     Author: Site Editor     Publish Time: 2026-08-27      Origin: Site

Inquire

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
kakao sharing button
snapchat sharing button
telegram sharing button
sharethis sharing button

3b1704b4d6a6cc1f3b662c31c2ebaa84

CUSTOM WINDING STRUCTURE

In-Process Three-Wire Twistingfor an EI14 Transformer



image
官网EI14_Custom_Winding_Structure_Website_Editable_01
PROCESS CASE STUDY

Custom Winding Structure:

In-Process Three-Wire Twisting for an EI14

Transformer


A practical look at how a defined three-wire twisting

operation is inserted into the winding sequence, then

followed by trimming, winding completion, and insulation wrapping.

图片5
EI14绕线工艺文章_02(1)

Why This EI14 Case Is Different


In a standard winding operation, the objective is usually to complete the specified turns and

insulation sequence with as few interruptions as possible. Some custom designs, however, contain a wire arrangement that must be formed at a defined point during winding. In this EI14 transformer

case, three fine magnet wires are gathered and twisted together after an initial winding stage, rather than being prepared only before winding begins.

The important point is not the manual action by itself. The process must preserve wire identity,

winding sequence, lead arrangement, and the required insulation structure before production

continues. The supplied production record shows a controlled sequence of partial winding, three-

wire twisting, wire trimming, winding completion, and tape wrapping.

EI14绕线工艺文章_03(1)
图片5
Initial winding stage - a portion of the winding is completed first.
图片6
Mid-process operation - three fine magnet wires are gathered and twisted.
EI14绕线工艺文章_03

Step-by-Step Implementation


图片7
01 - Initial Winding Stage
A portion of the winding is completed first, leaving the required wire section available for the next operation.This stage
establishes the correct point in the winding sequence before
the three-wire section is formed.
02 - In-Process Three-Wire Twisting
At the defined production stage, three fine magnet wires are gathered and twisted together. The supplied case study identifies this as a deliberate part of the winding sequence, not a separate finishing step. The wire arrangement must remain consistent with the approved design before winding can continue.
图片8
图片9
03 - Wire Trimming Before Winding Resumption
After twisting, the wire ends are trimmed to the required length. This prepares the wire group for the next winding operation
and prevents excess wire from interfering with the defined lead arrangement.
EI14绕线工艺文章_04(1)

Winding Completion and Insulation Control


Once the specified winding sequence is completed, insulation tape is applied to secure the winding and maintain the required insulation structure. The tape operation is therefore part of the structural implementation of the design, not simply a cosmetic finishing step.

图片10

Tape wrapping secures the completed winding and maintains the specified insulation structure.



EI14绕线工艺文章_05(1)(1)

What Should Be Controlled in Production?


• Process position: the twisting operation must occur at the correct point in the winding sequence.

• Wire arrangement: the three fine magnet wires must be gathered as specified before the next step.

• Trim length: the twisted wire ends are cut to the required length before winding resumes.

• Winding continuity: the subsequent winding operation must continue without changing the approvedstructure.

• Insulation execution: tape wrapping must secure the winding and maintain the required insulation arrangement.

EI14绕线工艺文章_05(1)(2)

Completed EI14 Winding Assembly


The finished winding assembly shows the result of the controlled production sequence. The three-wire feature is not treated as an isolated manual detail; it is implemented together with the winding order,lead arrangement, trimming, and insulation steps that define the finished transformer structure.

图片11

Winding assembly view



图片12

Completed taped winding and terminal arrangement



What This Case Demonstrates


This EI14 example illustrates a broader point in custom transformer manufacturing: a winding

drawing can contain operations that cannot always be reduced to one uninterrupted machine cycle.

When an intermediate operation is required, the manufacturing process must define when it occurs,

how the wire is handled, and how the winding resumes afterward.

For engineering and sourcing teams, this makes production review more meaningful than simply

asking whether a transformer is machine-wound or manually handled. The relevant question is

whether the approved winding structure can be reproduced in a controlled and repeatable way during batch production.

EI14绕线工艺文章_06(1)(1)

ONLINE MESSAGE

WhatsApp:+86 152 6187 0271
Email : shiyucao@inftechs.com
Add :  Building A1, No. 55 Runfa Road, Jiangning District, Nanjing, China

EMC/EMI Components

Power Inductors & Transformers

Copyright © 2026 Nanjing Infinity Technology Co., Ltd. All Rights Reserved. Sitemap. Privacy Policy.  苏ICP备2022036817号-2